Core Drilling in Canberra, ACT
Core drilling makes precise circular holes through concrete for plumbing, electrical, ventilation and structural services. It gives you a clean, accurately sized penetration so the next stage of your project can be installed with confidence.
About This Service
Core drilling removes a round section of concrete to form a clean hole at a specific diameter and position. It is the method used when a pipe, conduit, cable route, vent or anchor needs to pass through a slab, wall or footing. Instead of chiselling an irregular opening, the drill produces a measured penetration that can suit the service being installed. For a renovation in Canberra, that precision can save time when the plumber or electrician arrives.
You may need core drilling when a new bathroom needs waste pipes through a slab, an air-conditioning system needs a penetration, or a commercial fit-out requires new services. It is also useful where a route has to pass through concrete without opening up a much larger area. Homes in Gungahlin, Weston Creek and Narrabundah often have additions and upgrades where existing concrete constrains service routes. A correctly located hole helps avoid awkward offsets and unnecessary patching later.
Before drilling, we discuss the required hole size, location, depth, access and the service that will use it. We check the proposed point, establish the drilling angle where needed and set up the equipment securely to keep the hole accurate. For Canberra sites, we encourage customers to coordinate with the relevant trade and identify any known services before work begins. Water and slurry management are planned around the setting, especially for internal areas or finished spaces.
The result is a neat circular opening that is ready for the intended pipe, cable, duct or fixing system. Diamond core drilling can work through reinforced concrete, although the material, depth and access influence the time required. A small, accessible penetration may be completed promptly, while multiple holes across a larger fit-out are best planned around the construction schedule. Proper sizing is important because an oversized hole can create extra finishing work, while an undersized hole delays installation.
Capital Concrete Cutting has served the local region since 2018, with a focus on careful set-out and clear communication. We understand that core holes are often one small but critical part of a much bigger job, so we work to the dimensions and locations agreed for the scope. Whether the work is near the Parliamentary Triangle, along Northbourne Avenue or on a residential block, practical preparation helps us protect the area around the drilling point. You receive a straightforward answer about what is needed to complete the hole properly.
Bring us in early if your project involves new plumbing, electrical pathways, mechanical services or concrete penetrations. Photos, plans and the required diameter are useful starting points, particularly where access is limited or the drilling must be done at an angle. We assist customers across Canberra, Queanbeyan, Yass and Murrumbateman with planned, accurate core drilling. Contact us to discuss your opening requirements and arrange a quote.
Your Questions, Answered
Frequently Asked Questions
These answers cover the questions we hear most often before concrete cutting work begins. For site-specific advice, share the details of your project so the method can be matched to the conditions.
What hole sizes can be core drilled through concrete?
Core drilling can create a wide range of hole diameters, but the best size is determined by the pipe, conduit, duct or fixing system being installed. Your plumber, electrician, air-conditioning technician or engineer can usually nominate the required penetration size. We then assess the concrete thickness, access and drilling position. Providing that information before booking helps ensure the equipment and set-up match the job.
How long does core drilling take in Canberra?
A single accessible core hole may take a relatively short on-site visit, while deeper reinforced concrete, difficult access or multiple locations add time. Set-up, accurate positioning and water or slurry control are important parts of the work, not afterthoughts. Jobs in occupied spaces may also need extra protection and coordination. Once we understand the hole sizes, depths and conditions, we can give a realistic timeframe for the scope.
Does core drilling create a lot of mess indoors?
Core drilling uses water to support the diamond drilling process, so slurry management needs to be considered before work starts. We plan containment around the drilling location and discuss access, floor protection and nearby finishes with you. The core removed from the hole is contained rather than shattered across the area. Internal jobs benefit from clear preparation and a suitable work zone.
Do I need to know where services are before core drilling?
Yes, known service information is important before any concrete penetration is drilled. Share plans, service locations and advice from the trade installing the new line, particularly for slabs and walls near kitchens, bathrooms or switchboards. If the location is uncertain, it should be clarified before drilling proceeds. Careful set-out protects the project and helps place the hole where it will actually be useful.
Start Your Concrete Cutting Project Today
Talk with a local team that understands the practical demands of Canberra sites. Request a free estimate and get a clear path forward for your concrete-cutting work.
0495 050 252Or fill out the form — we'll be in touch shortly.